Dictionary USA Cars

Un utile strumento per chi non ha dimestichezza con i termini tecnici relativi al mondo delle auto USA. Si ringrazia The Muscle Car Club per averci permesso di utilizzare le loro informazioni.

DIZIONARIO

Air Bag: The air bag, also known as a Supplemental Inflatable Restraint System, is a passive safety device, supplemental to safety belts, that inflates to provide a cushion to absorb impact forces during moderate to severe frontal collisions. This system can help to lessen the chance of contact with the steering wheel, instrument panel and windshield. The air bag is actuated automatically by sensors located in the front of the vehicle. To maximize effectiveness, seat and shoulder belts must always be used in conjunction with this system.

Air Injection: A system that injects air into the exhaust ports of the engine for combustion of unburned hydrocarbons in the exhaust gases, thus producing “cleaner” exhaust emissions.

Airfoil: An aerodynamic device designed to improve traction by increasing the downforce on the car. The use of airfoils (also called spoliers or wings) increases the cornering capability and improves stability at speed, but often at the expense of additional aerodynamic drag.

Alignment: Generally refers to wheel alignment, which is the proper adjustment of the car’s front and rear suspension for camber, toe, caster and ride height.

Alloy Wheels: A generic term used to describe any non-steel road wheel. The most common alloy wheels are cast aluminum. Technically, an alloy is a mixture of two or more metals. These wheels are known for their light weight and strength.

All-Wheel Drive: Often confused with Four-Wheel Drive (4WD), this drive system features four, full-time active drive wheels to reduce wheel slippage and provide greater driver control over the vehicle. All-Wheel Drive automatically splits engine torque between the front and rear wheels as needed, improving on-road traction in unfavorable road conditions. Unlike Four-Wheel Drive, All-Wheel Drive is an on-road system and is not designed for off-road use. AWD does not require the driver to actively engage the system. It is operational at all times, and requires no switches, lights or visor instructions for system operation.

Anti-Lock Brake System (ABS): On a vehicle equipped with Anti-Lock Brakes, the wheels are equipped with speed sensors. When a sensor determines that a wheel is decelerating so rapidly that lockup may occur, the electro-Hydraulic Control Unit (EHCU) is activated. The EHCU then modulates the brake pressure in the appropriate brake lines by means of the solenoid-operated valves. This is intended to prevent wheel lockup and help the vehicle maintain directional stability during potentially hazardous braking situations. (See also

A-Pillar: In the side view, the foremost roof support of a vehicle, located in most instances between the outer edge of the windshield and the leading edge of the front door upper. Also known as an A-Post.

Automatic Locking Front Hubs: Found in some four-wheel drive vehicles, this allows the driver to engage, or “lock,” the front axle hubs without leaving the vehicle.

Axle Ratio: The ratio between the rotational speed (RPM) of the drive shaft and that of the driven wheel. Gear reduction in final drive is determined by dividing the number of teeth on the ring gear by the number of teeth on the pinion gear.

Balance Shaft: A shaft designed so that, as it turns, it counter rotates the rotational direction of the engine crankshaft in a manner that reduces or cancels out some of the vibration produced by the engine.

Ball Joint: A flexible joint consisting of a ball within a socket. Ball joints act as pivots which allow turning of the front wheels and compensate for changes in the wheel and steering geometries that occur while driving.

Base Coat/Clear Coat: A paint system that adds a final clear-coat paint layer over primer and color coats to provide a deep, “wet-look” shine that resists fading.

Belted Radial Tires: A reinforcing bank, normally textile, fiberglass or steel, running around the circumference of a tire and strengthening the tread area. The most common type of tire available today.

Bias-Ply Tires: A type of tire in which the plies or layers of cord in the tire casing are laid diagonally, criss-crossing one another at an angle of 30 to 40 degrees. Often the original type of tires found on muscle cars.

Body-On-Frame Construction: A type of automobile construction in which the body structure is attached to a separate frame. Common on cars until the 1970′s when car companies switched to uni-body construction on most cars (but not on trucks and some SUVs).

Boost: The amount of extra air (compressed air) pumped into the intake manifold by a supercharger or turbocharger. Usually measured in psi (pounds per square inch), inches of mercury, or bar.

Bore: The diameter of an engine cylinder or bearing. Used in determining engine displacement.

B-Pillar: The roof support between a vehicle’s front door window and rear side window, if there is one.

Brake Fade: A condition brought about by repeated brake applications, resulting in build-up of heat that causes a temporary reduction or fading of braking effectiveness.

Brake Horsepower (bhp): The actual horsepower of an engine, measured by a brake attached to the driving shaft and recorded by a dynamometer.

Brake Linings: The replaceable friction material which contacts the brake drum in a drum brake system to slow or stop the car.

Brake Master Cylinder: A cylinder containing a movable piston activated by pressure on the brake pedal. The piston produces hydraulic pressure that pushes fluid through the lines and wheel cylinders. This forces the brake lining or pad against the drum or disc to slow or stop the car.

Brake Pads: In a disc system, they are the replaceable flat segments consisting of a rigid backing plate plus frictional lining that takes the place of the shoe and lining in a drum brake. Brake pads are sometimes referred to as brake pucks.

Brake Shoe: The arc-shaped carrier to which the brake linings are mounted in a drum brake. They also force the lining against the rotating drum during braking.

Brakes, Disc: A type of braking system in which brake shoes, in a vise-like caliper, grip a revolving disk mounted on a wheel to slow or stop disc and wheel rotation for braking. Properly called “Caliper Disc Brakes,” they are used on most modern cars.

Brakes, Drum: A type of braking system that utilizes a metal drum mounted on a wheel to form the outer shell of a brake. The brake shoes press against the drum to slow or stop drum and wheel rotation for braking. Common on vehicles in the ’60s and ’70s, Drum brakes are only used on some vehicles rear wheels today.

Burned Piston: When a cylinder runs lean (too much air in the air-to-fuel mixture) and excessive heat burns or melts the piston.

CAFE: The acronym for Corporate Average Fuel Economy. This single mileage figure is determined by taking a sales weighted average of the fuel consumption for all models produced by a manufacturer. The minimum required figure is an established U. S. government standard. Manufacturers which do not meet the minimum standard are fined.

Caliper: In a disk brake, a housing for cylinder, pistons and brake shoes, connected to the hydraulic system. The caliper holds the brake shoes so they straddle the brake disc.

Cam Gear / Adjustable Cam Gear: The cam gear is connected to the end of the camshaft. The timing belt connects the cam gear to the crank. An adjustable cam gear allows you to adjust the cam without removing the timing belt.

Cam Profile: The shape of each lobe on a camshaft.

Camber: The angle along the vertical axis of the tire/wheel when looking at the car directly from the front or the rear. Positive camber results when the top of the tire tilts out further than its bottom. Negative camber is vice-versa, and a little bit of negative camber may actually improve handling. The adjustment of this setting affects both tire wear and vehicle handling.

Camshaft: The shaft in the engine which is driven by gears, belts or chain from the crankshaft. The camshaft has a series of cams that opens and closes intake and exhaust valves as it turns.

Caster Angle: The forward or backward tilt of the steering axis as viewed from the side. If the point of load is ahead of the point of contact, the caster angle is positive. The caster angle tends to keep wheels in a straight line. Proper caster adjustment improves both tire wear and fuel economy.

Catalytic Converter: Often simply called a “catalyst”, this is a stainless steel canister that is part of a vehicle’s exhaust system and contains a thin layer of catalytic material spread over a large area of inert supports. It induces chemical reactions that convert an engine’s exhaust emissions into less harmful products prior to entering the environment. Made required for all vehicles sold in the U.S. starting in 1978. A car equiped with a catalytic converter cannot use leaded fuel, as it will damage the Catalytic converter.

Center of Gravity: Point where the weight of a vehicle appears to be concentrated and if suspended at that point would balance front and rear.

Closed Crankcase Ventilation (CCV): A system in which crankcase vapors are discharged into the engine intake system (usually via the intake manifold) where they are burned during the combustion process rather than being discharged into the atmosphere.

Clutch Can: The bell-shaped housing, or bellhousing, used to encase the clutch and flywheel.

Clutch Dust: Carbon dust created when the surface of the clutch discs wear as they slide together during the clutch-lockup process.

Clutch Lock-Up: The progression of clutch-disc engagement controlled by an air-timer management system.

Coefficient of Drag (cd) or Drag Coefficient: A measure of the aerodynamic sleekness of an object. The lower the number, the greater the aerodynamic efficiency. The higher the drag coefficient, the more a car’s engine must work to keep a given road speed.

Cold Cranking Amps (CCA): A rating, measured in amperes. Used for comparing cranking strength of automotive batteries during extremely cold (0 F or lower) weather. The higher the CCA, the better.

Combustion Chamber: The volume of space at the top of the cylinder where burning of the air/fuel mixture begins.

Composite Headlamps: Usually manufactured with replaceable halogen bulbs and separate hard acrylic or glass lenses. This type of lamp provides superior illumination compared to the long-conventional sealed beam unit.

Compression Ratio: The volume of the combustion chamber and cylinder when the piston is at the bottom of its stroke, divided by the volume of the combustion chamber and cylinder when the piston is at the top of its stroke. Higher compression ratios tend to increase engine efficiency.

Compressor (Air Conditioning): The machinism is an air conditioner that pumps vaporized refrigerant out of the evaporator, compresses it to a relatively high pressure, and then delivers it to the condenser.

Condenser: A device for storing electrical energy. In A/C application, an air conditioning component used to remove heat from the inside of a vehicle.

Connecting Rod: The metal rod that connects a piston to the crankshaft.

Contact Patch: The area of a tire’s tread that is in contact with the ground.

Control Arm: A suspension element that has one joint at one end and two joints at the other end, typically on the chassis side. Also known as a wishbone or an A-arm.

Coolant: The mixture of water and anti-freeze that picks up heat from the engine and transfers it to the air passing through the radiator. This transfer of heat keeps the engine operating within its optimum temperature rant preventing premature engine wear.

Cooling System: The system that removes heat from the engine by the forced circulation of coolant and thereby prevents engine overheating. In a liquid-cooled engine, it includes the water jackets, water pump, radiator, and thermostat.

C-Pillar: The roof support between a vehicle’s rearmost side window and its rear window. Also known as a C-Post. On a vehicle with four side pillars, the rearmost roof support may be called a D-pillar.

Crankcase: A case that encloses the crankshaft. In most engines, the oil pan and the lower portion of the cylinder block form the crankcase.

Crankshaft: A shaft with one or more cranks, or “throws,” that are coupled by connecting rods to the engine’s pistons. The combustion process creates reciprocating motion in the rods and pistons which in turn is converted to a rotating motion by the crankshaft.

Crossmember: One of several horizontal members in a vehicle frame which join the side members and add to overall strength and stability.

CV Joint: Constant Velocity Joint — a type of universal joint used in the transaxle. They ensure that the input and output shafts are rotating at the same rate.

Cylinder Block: The basic part of the engine to which other engine parts are attached. It is usually a casting and includes engine cylinders and the upper part of the crankcase.

Cylinder Head: The removable part of the engine that attaches to the cylinder block directly above the cylinders. The head is cast from aluminum or iron and houses the combustion chambers, the intake and exhaust ports, spark plugs and much or all of the valve train. It has oil and water passages for cooling and lubrication.

Detonation: Occurs when hot spots (caused by engine deposits) in the combustion chamber ignites the air and fuel mixture prematurely. Also occurs after combustion if any unburned fuel is left in the combustion chamber. Also known as engine knock. Places great stress on the engine and leads to the destruction of the engine if ignored.

Diesel Engine: A diesel engine uses heavier weight components than gas engines to handle higher compression ratios. Typically, diesel engines run with greater efficiency and higher torque than similar size gas engines. These attributes lead to better fuel economy and towing performance. Diesel engines do not have spark plugs or carburetors. Instead glow plugs are used to preheat air in the cylinders to ensure easy starts. Once the engine is started, compression heats the fuel in the cylinders for combustion.

Dieseling: A condition in which gasoline continues to fire after the ignition has been shut off. In late-model engines, dieseling, or run-on, is caused by heat and the unusually high manifold pressure that result from retarding the spark at idle. In fuel-injected cars when the engine is turned off, fuel is automatically shut off, eliminating dieseling.

Differential: The gear assembly connected to the drive shaft that permits the wheels to turn at different speeds when going around a corner, while transmitting power from the drive shaft to the wheel axles.

Differential, Locking
: The same attributes of a standard differential, except that when one wheel is slipping, the most torque is supplied to the wheel with best traction. A locking differential reduces the possibility of a vehicle becoming immobile when one driving wheel loses traction.

Directional Stability: A vehicle’s ability to maintain a true course of travel despite bumps, crosswinds, uneven road surfaces.

Displacement: In an engine, the total volume of air or air-fuel mixture an engine is theoretically capable of drawing into all cylinders during one operating cycle. Generally expressed in liters or cubic inches. Engine displacement is equal to the engine bore x stroke x number of pistons.

Distributor: A component of the ignition system, usually driven by the camshaft that directs high-voltage surges to the spark plugs in the proper sequence.

Double Wishbone Suspension (“A” Arm Suspension): A system of independent suspension in which each wheel is located on a “knuckle” that is connected by ball joints to an upper A arm and a lower A arm. Usually, the lower A arms are longer. This system provides minimal changes in track and camber when the suspension is under load, as when going over bumps or in hard cornering.

D-Pillar or D-Post: The vertical or sometimes diagonal roof supporting member located at the extreme rear of the roof or greenhouse structure on station wagons and some sedan models.

Drive Shaft: The shaft that transmits power from the transmission to the differential in a rear-drive power train.

Drive Train: The power-transmitting components in a car, including clutch, gearbox (or automatic transmission), driveshaft, universal joints, differential and axle shafts.

Dropped Cylinder: When a cylinder becomes too rich (too much fuel in the air-to-fuel mixture) and prevents the spark plug(s) from firing.

Dual Overhead Camshafts (DOHC): A DOHC engine has two camshafts in each cylinder head; one camshaft actuates intake valves and the other actuates exhaust valves. The camshafts act directly on the valves, eliminating pushrods and rocker arms. This reduced reciprocating mass of the valve train enables the engine to build RPM more quickly. DOHC designs are typically high-performance, four valve per cylinder engines. (A four valve per cylinder two intake and two exhaust design helps the engine “breathe” more freely for increased performance.)

Dynometer: A device which absorbs and measures the power derived by an internal combustion engine.

Electrolyte: Any solution that conducts an electrical current, such as a mixture of sulfuric acid and distilled water found in automotive batteries.

Electronic Control Unit (ECU): The computer that receives signals from various sensors and determines how much fuel to inject into the engine under various conditions.

Electronic Fuel Injection (EFI): A system that injects fuel into the engine and includes an electronic control unit to time and meter the fuel flow. The standard in all vehicles since the late 1980′s, but was available on 1950′s Corvettes.

Electronic Ignition System: An ignition system that uses transistors and other semiconductor devices as an electronic switch to turn the primary current on and off.

EPA Fuel Economy Rating: Comparative mileage figures generated from laboratory fuel-economy tests administered by the federal Environmental Protection Agency (EPA) using simulated weight and drag to approximate real driving conditions.

Exhaust Gas Recirculation (EGR): An exhaust-emission control system in which a portion of the exhaust gas is picked up from the exhaust manifold and sent back to the intake manifold to be reburned in the engine. Mixing exhaust gases with the fresh air/fuel mixture lowers the combustion temperature and reduces the formation of oxides of nitrogen in the exhaust.

Exhaust Manifold: The network of passages that gathers the exhaust gases from the various exhaust ports and routes them toward the catalyst, the muffler and the exhaust system.

Factory Equipment: The combination of original standard equipment and production options installed at the factory that make up the equipment of a vehicle. Does not include any accessories installed by a dealer.

Fifth Wheel: Load supporting plate mounted to the frame of a vehicle. Pivot mounted, it contains provision for accepting and holding the kingpin of a trailer, providing a flexible connection between the tractor and the trailer. Center of the fifth wheel should always be located ahead of the centerline of the rear axle.

Final Drive Ratio: A fluid coupling consists of two fan-like impellers in a sealed, oil-filled housing. The input “fan” churns the oil, and the churning oil, in turn, twirls the output “fan.” Such a coupling allows some speed difference between its input and output shafts. The automatic transmission’s torque converter is based on the fluid coupling principle.

Flywheel: A large, heavy disc that is attached to the end of the crankshaft. It adds inertia to the engine which results in smoother power flow.

Forced Induction: Any method used to force more air into the combustion chamber. Nitrous, turbo, supercharger, and everything in between.

Four Wheel Drive (4WD): In a Four Wheel Drive system, a secondary transmission assembly, called a transfer case, is driven from the main transmission. The transfer case distributes power to both axles to drive all four wheels. It is the heart of the Four-Wheel Drive system. Four-Wheel Drive can be full-time, in which power is delivered to both axles at all times or part-time, where the driver selects two or four wheel drive. Four wheel drive is often combined with independent suspension systems and off-road type tires to enhance driveability on rough, off-road terrain, or on-road driveability in unfavorable driving conditions.

Four Wheel Independent Suspension: A type of suspension in which all wheels are mounted to separate suspension members with no rigid axle connecting them. Therefore a disturbance affecting one wheel has no effect on the opposite wheel. Four wheel independent suspension reduces the un-sprung weight, improves ride and handling over rough surfaces and permits room for a larger trunk.

Front Wheel Drive: A drive system where the engine and transaxle components apply the driving force to the front wheels rather than the rear wheels. Benefits of Front-Wheel drive include

Fuel Injection: A fuel-delivery system that replaces conventional carburetion. Fuel injection delivers fuel under pressure directly into the combustion chamber or indirectly through the airflow chamber.

Fuel Pump: A mechanical or electrical device that draws fuel from the fuel tank and delivers it to the carburetor or injectors.

Galvanized Steel: A specially zinc-coated steel used on many major painted panels and in key unpainted areas of a vehicle to help prevent rust and corrosion.

Gas Filled Shock Absorbers: A nitrogen gas chamber is used to pressurize the shock absorber in place of the traditional air/oil combination. Gas filled shock absorbers provide more stable damping in a variety of conditions and thus improves ride and road contact.

Gear Ratio: The number of revolutions a driving (pinion) gear requires to turn a driven (ring) gear through one complete revolution. For a pair of gears, the ratio is found by dividing the number of teeth on the driven gear by the number of teeth on the driving pinion gear.

Generator: A device that converts mechanical energy into electrical energy. It can produce either AC or DC electricity. Seldom used in automotive applications, it has been replaced by the alternator.

Halogen Headlamp: A sealed-beam headlamp with a small inner bulb filled with halogen which surrounds a tungsten filament. Halogen headlamps may increase luminous intensity at the road surface by 50 to 80 percent, as compared to the long-conventional sealed-beam headlamp systems. Many halogen headlamp systems incorporate high-beam and low-beam in one element, enhancing their serviceability.

Headers: Fine-tuned exhaust system that routes exhaust from the engine. Replaces conventional exhaust manifolds.

Heads Up Display: The digital projection of pertinent instrument data onto the lower portion of the windshield on the driver’s side. The driver does not have to take his eyes off the road to read his instrument panel.

Heel and Toe: A technique used by racing drivers that involves the use of all three pedals in a manual transmission equipped automobile. During shifting, the toe of the right foot controls the brake, while the heel of the same foot depresses the gas pedal. The left foot, of course, depresses the clutch. When executed properly, the effect is a smooth and efficient transfer of power between shifts.

Hemi: A hemi engine has a hemispherically shaped cylinder-head combustion chamber, like a ball cut in half.

Horsepower (also Brake Horsepower): A unit of measure used in representing the amount of energy or power produced by a device — one horsepower is equal to the energy required (work) to move a 550 pound object one foot in one second. Also equivalent to 746 watts.

Hydraulic: When a cylinder fills with too much fuel, thus prohibiting compression by the cylinder and causing a mechanical malfunction, usually an explosive one.

Independent Suspension: A term used to refer to any type of suspension system that allows each of the two wheels of a given axle to move up and down independently of each other.

Intake Charge: The mixture of air and fuel that flows into the intake manifold.

Lean Condition: Refers to an air/fuel mixture that has more air than fuel – which may lead to detonation.

Limited Slip Differential: A specially designed differential that not only allows the left and right axles to spin independently, but also has the ability to distribute the power to each axle even if one is slipping due to the loss of traction. A Limited Slip Differential ensures that some torque is always distributed to both wheels, even when one is on a very slipper surface.

Lock Up Torque Converter: A torque converter that contains a special clutch that forms a solid connection between the engine output shaft and the transmission input shaft when a certain, pre-set speed is attained. This reduces transmission friction losses and increases efficiency.

Lockup Differential: A differential that locks the two outputs (axles) together, so there is no differential action giving you maximum traction. Generally used for drag racing where no steering is needed.

MacPherson Strut: A suspension system that consists of a combination coil spring and shock absorber in one compact unit at each wheel. With this “independent” suspension design, road shocks at one wheel are not transferred to the opposite wheel. MacPherson struts use fewer parts, meaning a reduction on weight and fewer elements that could wear out.

Main Bearings: The bearings in the engine block that supports the crankshaft.

MAP Sensor: Manifold Absolute Pressure sensor

Multi-Port Fuel Injection (MFI): Multi-Port Fuel Injection uses individual fuel injectors to spray fuel into each intake port, bypassing the intake manifold.

Naturally Aspirated: Refers to an engine that does not use any form of forced induction to achieve more performance.

Neutral Steering: A condition in which the slip angle of the front and rear wheels are the same.

Nitrous Oxide (NO2): Nitrous oxide is a compound that is made up of two parts oxygen to one part nitrogen. A gas at room temperature and a liquid under pressure. When heated, it breaks down into its two elements. Often used in racing as a source of compressed air that can be forced into the motor for short periods of greater power.

NOS: Brand name/logo for Nitrous Oxide Systems

Octane Rating: A unit of measurement on a scale intended to indicate the tendency of a fuel to detonate or knock based on the percentage of isooctane in the fuel. The higher the rating, the higher the percentage of isooctane and therefore the greater the resistance to detonation offered by the fuel.

Overdrive: A gear set in which the output shaft rotates faster than the input shaft, i.e. the highest gear ratio is less than a one-to-one ratio. The overdrive feature saves fuel and, because the engine runs slower, engine wear and noise are reduced.

Overhead Cam: The type of valve train arrangement in which the engine’s camshaft is mounted above the cylinder head(s). When the camshaft is placed close to the valves, the valve train components can be stiffer and lighter, allowing the valves to open and close more rapidly and the engine to run at a higher RPM. In a single overhead cam (SOHC) layout, one camshaft actuates all of the valves in a cylinder head. In a dual overhead camshaft (DOHC) layout, one camshaft actuates the intake valves, and one camshaft operates the exhaust valves.

Overhead Valve Engine (OHV): An engine with both intake and exhaust valves placed directly over the piston. In this design, the camshaft is located in the block, and the valves are actuated by pushrods and rocker arms.

Oversteer: Where the slip angle of the rear wheels are greater than that of the front wheels. The rear tires lose grip before front tires do. Happens more often in rear wheel drive cars.

Parasitic Drag: Anything that robs power from the engine via pulleys (air conditioners, alternators, power steering, water pump, etc.) and direct connection.

Pearl Paint: A type of paint that is similar to metallic paint, but instead of minute metal particles, it uses mica. Mica is a kind of semi transparent, crystalline mineral that absorbs and reflects light in prismatic fashion. This gives a dramatic, multi-dimensional effect to the paint. Sometimes called “pearl coat.”

Pinion: A gear with a small number of teeth designed to mesh with a larger geared wheel or a rack. Used in rack and pinion steering and the differential ring and pinion.

Piston: A partly hollow cylindrical part closed at one end, fitted to each of the engine’s cylinders and attached to the crankshaft by a connecting rod. Each piston moves up and down in its cylinder, transmitting power created by the exploding fuel to the crankshaft via a connecting rod.

Pitch: The up and down movement along an imaginary axis between the front and rear of a vehicle. Often during hard braking, the vehicle’s nose will “dive” or pitch down in front. During acceleration the back end will “squat” or pitch down in the rear.

Planetary Gears: A gear set, generally found in automatic transmissions, in which all of the gears are in one plane, grouped around each other like planets around the sun. The central gear is called the “sun gear.”

Plies: The layers of cord, fiberglass, steel or structural fabric that make up the tire carcass and reinforcing belts.

Ply Rating: A measure of the strength of tires based upon the strength of a single ply of designated construction. An eight-ply rating does not necessarily mean the tire has eight plies, but rather that the tires has the strength of eight standard plies.

Polishing: Smoothing an engine’s interior surfaces, usually the cylinder heads, to improve flow characteristics and/or to prevent hot spots.

Porting: Resizing an opening so it is matched with a mating surface.

Pound-Feet (lb-ft): A unit of measure used to measure torque, that is equivalent to a twisting force of one pound placed on a one foot long lever. Generated by the engine, torque is the “push” that sets a vehicle into motion and accelerates it. Specifications charts usually include the maximum torque the engine can develop, and the RPM at which it is generated (such as 345 lb.-ft. @ 3200 RPM).

Power: Usually measured in horsepower, power is proportional to torque and rpm.

Power Band: An rpm range where the majority of the engine’s peak power is achieved. Usually starts just below engine’s peak torque and ends just above the engine’s peak power.

Power Shifting: Refers to shifting gears without lifting the foot off the gas pedal. Shifting must be done quickly or the engine will rev too high. Don’t let the engine rev more than 500 rpm between shifts. Not for the uncoordinated!

Powertrain: A name applied to the group of components used to transmit engine power to the driving wheels. It can consist of engine, clutch, transmission, universal joints, drive shaft, differential gear, and axle shafts.

Predetonation: The undesirable “knock” or “ping” that occurs when the ignition of the air-fuel mixture occurs before the ignition spark. Also known as “pre-ignition”.

Progressive Rate Springs: A spring that is designed to be stronger as it is compressed. If it takes 50 pounds of force to compress the spring one inch, it would take more than 100 pounds of force to compress it an additional inch and so on.

PSI: Pounds per square inch — used to measure pressure. Normal atmospheric pressure at sea level is 14.7 psi.

Pushrod: A general term for any rod that transfers force in compression. In a conventional overhead valve layout, pushrods are used to transfer reciprocating motion from the cam followers to a more distant part of a valve train, typically the rocker arms. Pushrods are eliminated in overhead camshaft designs.

Quarter Panel: A sheet metal panel that covers the area from the rear-door opening to the taillight area, and from the bottom of the surface to the base of the roof, or from the headlamp area to the front-door opening, and from the bottom of the surface to the base of the hood.

Quartz Halogen Headlamps: A headlamp bulb having a quartz envelope holding the tungsten filament and filled with an inert gas containing iodine or another of the five halogen gases. The gas serves to remove the tungsten deposits from the bulb wall and redeposit them on the filament, preventing blackening of the bulb surface and reduction of light output. This kind of cycle requires very high filament operation temperatures which necessitates the use of quartz instead of glass. These lamps produce more lighting power per watt of electrical power than standard sealed beam headlamps.

Rack and Pinion Steering: A steering gear in which a pinion on the end of the steering shaft merges with a rack of gear teeth on the major cross member of the steering linkage. When the steering wheel is turned, the pinion gear turns, moving the rack to the left or right, thus steering the wheels.

Redline: The maximum recommended rpms for an engine. Refers to the upper limits of the rpm scale where engine damage will most certainly occur – indicated on the tachometer by a red sector.

Resonator: A small auxiliary muffler that assists the main muffler in reducing exhaust noise.

Rich Condition: Refers to an air/fuel mixture that has more fuel than air – which may cause loss of power.

Ring-and-Pinion Gear: Any gear set consisting of a small gear (the pinion gear) which turns a large-diameter annular gear (the ring gear). Used in rear-drive differentials (rear ends) to transfer power from the driveshaft to the axle and wheels.

Rolling Radius: Tire-rolling radius is the distance from the center of the wheel to the road. Static radium applies when the vehicle is standing still. Dynamic rolling-radius described wheels in motion. The latter is used to measure tire revolutions per mile and is usually slightly higher than static radius.

Rolling Resistance: This is motion resisting force that is present from the instant the wheels begin to turn. On normal road surfaces, rolling resistance decreases with increased tire pressure and increases with vehicle weight. Rolling resistance can also be affected by tire construction and tread design.

RPM: Revolutions per minute, or rpm, is a measure of engine speed as determined by how many full turns the crankshaft makes in a minute.

SAE: Abbreviation for Society of Automotive Engineers, A professional organization that sets standards for measuring horsepower and torque and for many automotive products such as fasteners, lenses, and lubricants.

Sealed Beam Headlamp: A one piece, hermetically sealed headlamp in which the filament is an integral part of the unit and the lens itself is the bulb. Sealed beams are relatively inexpensive and when one burns out or the lens cracks, the whole unit is replaced.

Slider Clutch: A multi-disc clutch designed to slip until a predetermined rpm is reached. Decreases shock load to the drive wheels.

Slip Angle: The difference in angles between the plane of the wheel and the rolling direction of the tire.

SOHC: Single Overhead Cam — engine designed to have one camshaft control both intake and exhaust valves.

Spoiler: An aerodynamic device, normally on the rear of the vehicle, that changes the direction of airflow in order to reduce lift or aerodynamic drag. A spoiler either reduces drag or create a downward force on the car. It is called a spoiler because it “spoils” the normal air flow over the car.

Springs, Torsion Bar: A long straight bar that is fastened to the frame at one end and to a control arm at the other. Spring action is produced by a twisting of the bar.

Steering Ratio: A predetermined ratio of the steering gears. Usually, the lower the steering ratio, the quicker the response.

Stoichiometric Condition: A condition in which you have an ideal mixture of fuel and air – between lean and rich. Correct stoichiometry is reached when you have 14.7 parts of air to 1 part fuel (gasoline). Perfect combustion.

Stroke: The distance the piston travels from bottom dead center to top dead center within the cylinder.

Strut: The main support member in a MacPherson suspension system. The strut also serves as the shock absorber.

Supercharger, Supercharged: A method of forced induction in which air is forced into the intake manifold via a turbine attached to the crank pulley. Although the term supercharger usually describes a device which does the above, it can also be used to describe any method of compressing air into the engine, including turbochargers!

Suspension System: Includes springs, shock absorbers/struts, and linkage used to suspend a vehicle’s frame, body, engine and drivetrain above the wheels.

Tachometer: An instrument for measuring the speed of the engine crankshaft in revolutions per minute (RPM).

TDC: Top Dead Center — when a piston is at the top most position during the compression stroke. TDC can also refer to the top most position of the piston in the exhaust stoke, but “true” TDC is on the compression stroke.

Throttle-Body: Throttle-Body Fuel Injection is a type of Electronic Fuel Injection which positions the injector(s) centrally in a throttle-body housing. This housing contains a valve to regulate the airflow through the intake manifold.

Timing: Timing refers to the crankshaft angles at which the valves open and close and at which time the ignition system fires the spark plugs.

Tire and wheel: Tire and wheel dimensions are the first point of information in any discussion of size and capacities. Among the other terms used to describe tires are tread, shoulder, carcass, sidewall, bead seal, bead seat, tire diameter, aspect ratio, speed rating and section width.

Tire Ratings: Tires are rated by load capacity, size and speed capacity. For example, a P225/50VR16 printed on the side of the tire means : P = P-Metric (Passenger Type Tire) 255 = Section Width (255mm) 50 = Aspect Ratio (tire height/section width) V = Speed Rating R = Type of Ply (Radial) 16 = Wheel Diameter (16 inches)

Toe In: The amount by which the front of a front wheel points inward or outward. A slight amount of toe in is usually specified to keep the front wheels running parallel on the road by offsetting other forces that tend to spread the wheels apart.

Torque: A force that produces a twisting or rotating motion.

Torque Converter Clutch: An electronically controlled lockup clutch that is automatically engaged at certain speeds to eliminate the slip between the torque converter’s input and output, thereby improving fuel efficiency and performance.

Torque Rating: A measure of the engine’s power capability, whereby the amount of twisting or rotating effort being exerted on the crankshaft is expressed in lb.-ft. of force. Torque is the force that gets the weight of the vehicle moving, making it an important consideration in trailering.

Torque Steer: A tendency for a car to steer to one side when power is applied. A condition that is particular to front wheel drive vehicles.

Torque, Engine: Engine torque is the amount of twisting effort exerted at the crankshaft by an engine expressed in foot-pounds of force. A foot-pound represents the force of one pound acting at the right angle to the rotating crankshaft at distance of one foot in length.

Torsion Bar: A long straight bar fastened to the frame at one end and to a suspension part at the other. In effect, a torsion bar is merely an uncoiled spring, and spring action is produced by twisting the bar. The main advantage of the torsion bar over the coil spring in the front suspension is the ease of adjusting the front suspension height.

TPS: Throttle Position Sensor. Measures the angle of the throttle plate and sends the information to the ECU.

Traction Control: Traction control helps provide smoother, more controlled acceleration by reducing the amount of wheel spin during reduced traction conditions. Traction control utilizes the vehicle’s anti-lock braking system and is usually activated only at low vehicle speeds.

Trailing Arm: A rear suspension element consisting of a lengthwise member that pivots from the body at its forward end and has a wheel hub rigidly attached to its trailing end.

Transaxle: A transmission and differential combined in one integrated assembly, eliminating the need for a separate connecting drive shaft. This configuration is typical in front-wheel-drive vehicles.

Tuned Intake and Exhaust Systems: Intake and exhaust systems that increase the flow of intake charge into and out of the combustion chambers by varying the length, shape, or diameter of the component.

Tuned-Port Fuel Injection (TPI): Tuned-Port Fuel Injection is almost identical to Multi-Port Fuel Injection, except that tuned runners are used to channel air to the cylinder heads. This results in increased airflow to the cylinders.

Turbo Lag: The time it takes for the turbocharger to spool up and thus start to take effect.

Turbocharger, Turbocharged: A method of forced induction in which air is forced into the intake manifold via a turbine that is powered by the exhaust from the engine.

Understeer: Where the slip angle of the front wheels are greater than that of the rear wheels. The front tires lose grip before rear tires do. The angle of the steering wheel is greater than normal – requires more steering by driver. Happens more often in cars equipped with front wheel drive. Slight understeer is actually a desired condition.

Unibody Construction: A type of body construction that doesn’t require a separate frame to provide structural strength or support for the vehicle’s mechanical components. Also called “unitized.” Common method of building today’s vehicles.

Universal Joint: A joint that transmits rotary motion between two shafts that aren’t in a straight line.

Valve: A device that can be opened or closed to allow or prevent the flow of a liquid or gas from one place to another. Most internal combustion engines use intake and exhaust valves to allow fuel/air mixture into the cylinders and to exhaust burnt gases. Some engines have four valves per cylinder, which increases total valve area for increased efficiency and performance.

Valve Float: When the valves in your engine are no longer controlled by the valve springs – will quickly lead to serious engine damage.

Valve Lifter: The cylindrical component that presses against the lobe of a camshaft and moves up and down as the cam lobe rotates, opening and closing an intake or exhaust valve. Virtually all modern valve lifters are of an hydraulic design that uses a cushion foil to promote quiet operation.

Valve Train: Refers to all the components that operate the valves (including the valves) in the engine’s cylinder head.

VTEC: Variable Valve Timing and Lift Electronic Control — A Honda proprietary system in which cam timing, valve duration and lift is varied according to the needs of the driver – fuel economy (normal driving) and power (pedal to the metal). Each cam has two profiles and rpm determines the shifting from one profile to the other.

Waste Gate: A device that limits the boost in a turbocharger via a valve. The waste gate bypasses the exhaust under certain conditions. Without a waste gate, a turbocharger will destroy an engine by over boosting the intake charge.

Wedge: An engine with a wedge combustion chamber, a combustion chamber resembling a wedge in shape. Need not have parallel intake and exhaust valve stems.

Weight Distribution: That portion of the total weight of a vehicle, including equipment and payload, that will be supported by each axle and tire. Proper distribution of total vehicle weight is critical to the performance handling of the vehicle, as well as the service life of components such as the frame, axles, springs, bearings, and tires.

Weight Transfer: Weight transfer is critical to traction. Vehicles are set up to provide a desired weight transfer to rear wheels. When the vehicle accelerates, the front wheels lift and the weight shifts to the rear wheels, which makes them less likely to spin.

Wheelbase: Distance, center to center, from front axle to rear axle. Wheelbase is important because it indicates available body length and weight distribution between front and rear axles.

Wheelie Bars: Used to prevent excessive front-wheel lift

WOT: Wide Open Throttle – Throttle is open all the way as in pedal to the metal, to let in as much air into the intake manifold as possible.